8 030 1 start up sheet packaged air conditioning unit

START-UP SHEET Packaged Air Conditioning Unit

Job Name ____

Job Number ____

Job Address ____

Section 5: Equipment Description

Spec. #: Submittal #: P&ID/Dwg #:
Area Served:
Data Design Actual On Site
Unit Tag #
Manufacturer
Model #
Serial #
Filter Description Pre-Filter Bag Filter Final Filter
Type
Size&Quantity
Size&Quantity
Belt Size
Size&Quantity

Section 6: Equipment Pre-Installation Inspection

Step Inspection Description Yes No N/A Performed By(Initials & Date)
6.1 Nameplate data matches vendor specifications. ☐ ☐ ☐
6.2 All parts are received. ☐ ☐ ☐
6.3 No visible signs of damage, leak, or defective parts. ☐ ☐ ☐

Observations

Performed By (Therma)

Reviewed By

(Owner/Representatives)

Print Name Signature Date

START-UP SHEET Packaged Air Conditioning Unit

Step Inspection Description Yes No N/A Performed By(Initials & Date)
6.4 Verify electrical service for correct voltage, current and thermal overload protection. $
Box$ $
Box$ $
Box$
6.5 Operational and Maintenance(O&M) manual is available in the field. $
Box$ $
Box$ $
Box$
6.6 Start-up technicians have reviewed factory start-up procedures in the O&M manual. $
Box$ $
Box$ $
Box$
6.7 If Therma provided Variable Frequency Drives(VFDs) that are controlling the fans, complete FN8.029.1 VFD start up form.
6.8 If Therma provided smoke fire dampers, complete form #FN8.061.1, smoke fire damper start up form.

Section 7: Installation Inspection

Step Inspection Description Yes No N/A Performed By (Initials & Date)
7.1 Unit is installed level. □ □ □
7.2 Tag # is attached to the unit. □ □ □
7.3 Service clearance is adequate for maintenance. □ □ □
7.4 Roof curb is installed to mate with the unit. □ □ □
7.5 All access panels and covers are in place. □ □ □
7.6 Vibration isolators are installed and adjusted. □ □ □
7.7 Ductwork and flex connections are connected and sealed. Make sure that roof ductwork has been connected to inside ductwork. □ □ □
7.8 Economizer or outside air damper is installed. □ □ □
7.9 All filters are in place and positioned properly. □ □ □
7.10 Condensate drain and trap are installed. □ □ □

Comments/

Performed By (Therma)

Reviewed By (Owner/Representatives)

Print Name Signature Date
Step Inspection Description Yes No N/A Performed By (Initials & Date)
7.11 Gas supply piping is installed. □ □ □
7.12 Gas supply piping has been checked for leaks. □ □ □
7.13 Gas supply piping is bled of air. □ □ □
7.14 Vent stack is proper height and size. □ □ □
7.15 Unrestricted vent cap on top to protect from weather and down drafts. □ □ □
7.16 Each fan drive belt tension is correct. □ □ □
7.17 Sheaves are aligned. □ □ □
7.18 Fan hub, sheaves and bearing setscrews are tight. □ □ □
7.19 Smoke detector is installed. □ □ □
7.20 Motor and blower bearings are lubricated. □ □ □
7.21 Crankcase heaters are installed. □ □ □
7.22 Fan bearings angular alignment is correct and bolts are tight □ □ □
7.23 Shipping blocks and materials removed from fan section. □ □ □
7.24 Electrical connections are secure. □ □ □
7.25 Thermostat is installed. □ □ □
7.26 Time clock is installed. □ □ □
7.27 Electric heat is installed □ □ □
7.28 Coils are clean and fins are straight □ □ □
7.29 All compressor shipping braces and compressor rail isolator sleeves are removed. □ □ □
Print Name Signature Date

START-UP SHEET Packaged Air Conditioning Unit

Step Inspection Description Yes No N/A Performed By(Initials & Date)
7.30 Compressor oil level is within manufacturer's specification. ☐ ☐ ☐
7.31 Low ambient control is installed. ☐ ☐ ☐
7.32 All condenser fan setscrews are tight. ☐ ☐ ☐

Section 8: Operational Inspection

Step Inspection Description Yes No N/A Performed By (Initials & Date)
8.1 Unit vibration is acceptable. □ □ □
8.2 Each fan rotation is correct. □ □ □
8.3 Natural gas supply pressure is at manufacturer’s specification. □ □ □
8.4 Manifold pressure is at manufacturer’s specification. □ □ □
8.5 Heating components perform per manufacturer’s specification. □ □ □
8.6 Cooling components perform per manufacturer’s specification. □ □ □
8.7 VAV components perform per manufacturer’s specification. □ □ □
8.8 Economizer components perform per manufacturer’s specification. □ □ □
8.9 Smoke detector is tested and is able to shut the unit down. □ □ □
8.10 Make sure thermostat is set. □ □ □

Comments/

Observations

Print Name Signature Date

START-UP SHEET Packaged Air Conditioning Unit

Step Inspection Description Yes No N/A Performed By(Initials & Date)
8.11 Make sure time clock is set. ☐ ☐ ☐
8.12 Crankcase heaters are functional. ☐ ☐ ☐
8.13 Fire dampers are functional and open. ☐ ☐ ☐
8.14 Supply, return and outside air dampers are functional. ☐ ☐ ☐
8.15 Record start up operating parameters in Supplementary Form(FN 8.028.2 or FN 8.028.3).

End of Section

Comments/ ____

Observations

Performed (Therma)

By

Reviewed By

(Owner/Representatives)

Print Name Signature Date