# START-UP SHEET

# Air Handling Unit

**Job Name Job Number**  
**Job Address**

## Section 5: Equipment Description

| Spec. #: | Submittal #: | P&ID / Dwg #: |
| --- | --- | --- |
| Area Served: |  |  |

| Data | Design | Actual On Site |
| --- | --- | --- |
| Unit Tag # |  |  |
| Manufacturer |  |  |
| Model # |  |  |
| Serial # |  |  |

## Record filter information below:

| Filter Description | Pre-Filter | Bag Filter | Final Filter |
| --- | --- | --- | --- |
| Type |  |  |  |
| Size&Quantity |  |  |  |
| Size&Quantity |  |  |  |

| Belt Description |  |  |  |
| --- | --- | --- |
| Size&Quantity |  |  |  |

## Section 6: Equipment Pre-Installation Inspection

| Step | Inspection Description | Yes | No | N/A | Performed By(Initials & Date) |
| --- | --- | --- | --- | --- | --- |
| 6.2 | Nameplate data matches vendor specifications. | □ | □ | □ |  |
| 6.3 | All parts are received. | □ | □ | □ |  |
| 6.4 | No visible signs of damage, leak, or defective parts. | □ | □ | □ |  |

## Comments/

**Observations**  
**Performed By**  
**(Therma)**  
**Reviewed By**

| Print Name | Signature | Date |
| --- | --- | --- |
|  |  |  |
|  |  |  |

**(Owner/Representatives)**

---

| Step | Inspection Description | Yes | No | N/A | Performed By(Initials & Date) |
| --- | --- | --- | --- | --- | --- |
| 6.5 | Verify electrical service for correct voltage, current and thermal overload protection. | □ | □ | □ |  |
| 6.6 | Operational and Maintenance(O&M) manual is available in the field. | □ | □ | □ |  |
| 6.7 | Start-up technicians reviewed factory start-up procedures in the O&M manual. | □ | □ | □ |  |
| 6.8 | If Therma provided Variable Frequency Drives(VFDs) that are controlling the fans, complete FN-8029.1 VFD start up form(s). |  |  |  |  |
| 6.9 | If Therma provided smoke fire dampers use form SFT-Test | □ | □ | □ |  |

**Section 7: Installation Inspection**

| Step | Inspection Description | Yes | No | N/A | Performed By(Initials & Date) |
| --- | --- | --- | --- | --- | --- |
| 7.2 | Unit is installed level. | $
| 7.3 | Tag # is attached to the unit. | $
| 7.4 | Service clearance is adequate for maintenance. | $
| 7.5 | Roof curb is installed to mate with the unit. | $
| 7.6 | All access panels and covers are in place. | $
| 7.7 | Vibration isolators are installed and adjusted. | $
| 7.8 | Ductwork and flex connections are connected and sealed. | $
| 7.9 | Economizer or outside air damper is installed. | $
| 7.10 | All filters are in place and positioned properly. | $
| 7.11 | Pressure and temperature taps are installed. | $
| 7.12 | Heating and cooling coil valves are mounted with actuator. | $
| 7.13 | Condensate drain and trap are installed. | $
| 7.14 | Auxiliary drain pan is installed and its connections are piped. | $
| 7.15 | All piping, coils,and valves are in place without leaks. | $
| 7.16 | Shipping blocks and materials are removed from fan section. | $
| 7.17 | Each fan drive belt tension is correct. | $
| 7.18 | Sheaves are aligned. | $
| 7.19 | Fan hub,sheaves,and bearing set-screws are tight. | $
| 7.20 | Smoke detector is installed. | $
| 7.21 | Motor and blower bearings are lubricated. | $
| 7.22 | Electrical connections are secure. | $
| 7.23 | Thermostat is installed. | $
| 7.24 | Time clock is installed. | $
| 7.25 | Fan shaft bearings angular alignment is correct and bolts are tight. | $
| 7.26 | Coils are clean fins are straight. | $

|  | Print Name | Signature | Date |
| --- | --- | --- |
| Performed By(Therma) |  |  |  |
| Reviewed By(Owner/Representatives) |  |  |  |

---

# START-UP SHEET

# Air Handling Unit

**Section 8: Operational Inspection**

| Step | Inspection Description | Yes | No | N/A | Performed By(Initials & Date) |
| --- | --- | --- | --- | --- | --- |
| 8.2 | Unit vibration is acceptable. | $
| 8.3 | Each fan rotation is correct. | $
| 8.4 | Heating water and cooling water control valves are functional. | $
| 8.5 | Fire dampers are functional and open. | $
| 8.6 | Supply, return and outside air dampers are functional. | $
| 8.7 | Smoke detector is tested and is able to shut the unit down. | $
| 8.8 | Make sure thermostat is set | $
| 8.9 | Make sure time clock is set | $
| 8.10 | Record start up operating parameters in the Supplementary Forms(FN 8.028.2 or FN 8.028.3). |  |  |  |  |

End of Section

**Comments/**

**Observations**

|  | Print Name | Signature | Date |
| --- | --- | --- |
| Performed By(Therma) |  |  |  |
| Reviewed By(Owner/Representatives) |  |  |  |